Je construis un récepteur IR avec PIC12F1572 avec module récepteur TSOP2438 Mon objectif de ce projet est de recevoir une donnée par télécommande et de l'envoyer au PC via UART .. J'ai fait le code et Je le teste Je peux envoyer la valeur normale à travers l'UART mais Somewhere a tort de sorte que je ne puisse pas recevoir les valeurs hexadécimales concernant les commandes de la télécommande Quelqu'un peut-il voir mon code et dire où je me trompe? Voici mon codeRécepteur IR RC5 avec Pic12F1572
void main(void)
{
OSCILLATOR_Initialize(); // 0x78 for Fosc = 16Mhz
PIN_MANAGER_Initialize(); //All port pins Digital and input
EUSART_Initialize();
INTCONbits.IOCIF = 0; // Interrupt on-change Flag
INTCONbits.PEIE = 1; //SEt Peripheral Interrupt
INTCONbits.GIE = 1; //Set Global Interrupt
//while(!OSCSTATbits.HFIOFS); //Check here or wait here to OSC stable/ 0.5% accuracy
TRISAbits.TRISA2 = 1; //Configure R1 as input
// uint16_t Input_buffer [20];
EUSART_Write(0x40); // 0x40 = @ some flag
while(1)
{
count = 0;
//while((IR_PIN)); //IR_PIN receives an IR signal its output pin goes from logic 1 to logic 0
//which causes the microcontroller to start reading the IR signal using the function. decode()
EUSART_Write(0x41);
//while(IR_PIN);
if(Decode()) //check if RC5 decoding- new data is arrived
{
EUSART_Write(0x42);
toggle_bit = bit_test(IR_Code, 11);
address = (IR_Code >> 6) & 0x1F;
command = IR_Code & 0x3F;
EUSART_Write(toggle_bit);
EUSART_Write(address);
EUSART_Write(command);
EUSART_Write(0x43);
}
}
}
/*----------*/
uint8_t Measure_space()
{
TMR0_Initialize();
while(IR_PIN && (count < 2000))
count = TMR0_ReadTimer(); //Read timer value and store it in count value
if((count > 1999) || (count < 700))
return 0; //0 = If width is out of range
if(count > 1200)
return 1; //1 = If width is long
else
return 2; //2 = If the width is short
}
uint8_t Decode()
{
uint8_t i = 0, check;
mid1:
check = Measure_Pulse();
if(check == 0)
return FALSE;
bit_set(IR_Code, 13 - i);
i++;
if(i > 13)
return TRUE;
if(check == 1)
goto mid0;
else
goto start1;
mid0:
check = Measure_space();
if((check == 0) && (i != 13))
return FALSE;
bit_clear(IR_Code, 13 - i);
i++;
if(i > 13) return TRUE;
if(check == 1)
goto mid1;
else
goto start0;
start1:
check = Measure_space();
if(check != 2)
return FALSE;
goto mid1;
start0:
check = Measure_Pulse();
if(check != 2)
return FALSE;
goto mid0;
}
Merci @ utilisateur7424291,, je vais mettre en œuvre – Garryp
Pouvez-vous tous me donner le vote s'il vous plaît? Je ne peux plus poster de question ... – Garryp